Home Inspections

Bellies in Furnace Intake and Exhaust Pipes

A high-efficiency furnace breathes through two plastic pipes, and both must slope continuously so water drains by gravity. When a pipe dips and rises again, it forms a low spot called a belly, and that belly fills with water.

How these pipes should run

A high-efficiency (condensing) gas furnace pulls combustion air in through one PVC pipe and pushes exhaust out through another. These furnaces extract so much heat from the exhaust that the water vapor in it condenses into liquid inside the pipe. That condensate is mildly acidic.

For this reason, the pipes must slope continuously, with no low spots. Depending on the manufacturer’s instructions, the slope runs either toward the exterior or back to the furnace, where the condensate trap and drain line carry the water away. A common requirement is at least 1/4 inch of fall per foot of pipe, with hangers spaced close enough to keep the pipe from sagging.

What I found at this inspection

Once in a while, I encounter furnace intake and exhaust pipes with low spots. This is usually the result of handyman work rather than a professional HVAC installation.

At this home, the pipes were routed from the furnace cabinet flush against the floor joists, then sloped down toward the exterior. On that path, the pipes would have met the foundation wall at a concrete block (CMU) course. Rather than core through the block, the installer flexed the pipes upward to exit through the wooden rim board above it.

That upward bend created bellies along the length of both pipes. It also left the outside ends angled upward, open to the weather.

Problems at the exhaust pipe

Condensate forms all along the exhaust pipe while the furnace runs. In a properly sloped pipe, it drains away. In a bellied pipe, it runs downhill into the low spot and stays there. Each heating cycle adds more.

  • Restricted exhaust flow. As the belly fills, the open space above the water shrinks. The furnace’s draft inducer motor has to push exhaust through a narrower and narrower gap.
  • Pressure switch shutdowns. Every condensing furnace has a pressure switch that confirms the vent is clear before the burners light. A partly flooded vent can trip that switch. The result is a furnace that fails to light, short-cycles, or locks out entirely, often on the coldest nights, when it runs hardest and makes the most condensate.
  • Gurgling and surging. Exhaust bubbling through standing water produces a gurgling sound. Slugs of water can also be pushed along the pipe in surges.
  • Freezing. Where a belly sits near the cold exterior wall, the trapped water can freeze and block the vent completely. The furnace then shuts down until the ice clears.
  • Stress on the joints. Standing, mildly acidic water adds weight to the pipe and sits against the glued joints. A sagging, water-loaded pipe pulls on its fittings. A joint that separates can leak water, and it can release exhaust gases, including carbon monoxide, into the basement.

Problems at the intake pipe

The intake pipe doesn’t produce condensate the way the exhaust does, but at this home it collects water from outside. Because the pipe was flexed upward to reach the rim board, its exterior opening angles up rather than down. Rain, wind-driven water and snowmelt can run into it, flow downhill and settle in the belly.

  • Starved combustion air. Water in the belly narrows the passage the furnace draws its air through. With less air than it was designed for, the furnace burns less cleanly and less efficiently.
  • Nuisance lockouts. A restricted intake can trip the same pressure switch as a restricted exhaust, causing failed ignitions and shutdowns.
  • Water reaching the furnace. Once the belly fills, more water entering at the termination has nowhere to go but toward the furnace. Water drawn into the burner area can corrode components that were never meant to get wet.
  • Blockage at the opening. An upturned opening also catches leaves, debris and drifting snow more readily than one that faces down or sideways.

The fix

The intake and exhaust pipes should be re-routed by a licensed HVAC contractor, following the furnace manufacturer’s installation instructions. That means:

  1. A continuous slope with no low spots, in the direction the manufacturer specifies.
  2. Hangers spaced closely enough to hold that slope over time.
  3. Exterior terminations that face the correct direction, with the required clearances from windows, doors, grade and each other.

If the only way to keep a proper slope is through the foundation wall, the block should be cored. The extra hour of work is small next to the cost of a furnace that can’t breathe.

If it’s left as is

The furnace will keep running into the problems above, and they will get worse with each heating season. Expect service calls for no-heat conditions and lockouts, avoidable wear on the inducer motor and pressure switch, and a growing risk of water damage and exhaust leaks at stressed joints.

This is the kind of condition I explain in detail in my reports: what was observed, why it matters, and what needs to happen next.

 

Findings Explained, Not Just Flagged.

Edwin Dunckley

Recent Posts

The Bathroom Fan That Never Sleeps

A bathroom exhaust fan that runs around the clock quietly pushes your heated or cooled…

2 weeks ago

Understanding Repaired Foundation Walls: What Do Those Vertical Patches Mean?

Foundation walls occasionally reveal signs of past movement and repair, and understanding these clues can…

2 weeks ago

Sediment Filters for Well Water: Choosing and Maintaining One

Every well carries some sediment: fine sand, silt, and clay from the ground around it.…

3 weeks ago

Hard Water and Dissolved Minerals: Hardness, TDS, Conductivity, and Chloride

Four results on your water report all describe the minerals and salts dissolved in your…

4 weeks ago

Nitrate and Nitrite in Well Water: Why Infants Matter Most

Most of the chemical results on a well water report are about taste, staining, or…

4 weeks ago

Acidic Well Water: What Your pH Result Means

Acidic water is one of the most common findings in well tests across our area.…

4 weeks ago